Mazda mx 6 mazda 626 service repair workshop manual 1988 1989. Mazda MX6 2019-02-14

Mazda mx 6 mazda 626 service repair workshop manual 1988 1989 Rating: 7,4/10 663 reviews

1988

mazda mx 6 mazda 626 service repair workshop manual 1988 1989

Tentatively secure the tensioner with the spring fully extended. Timing belt Refer to Section 1 4. Cleaning parts for reuse All parts to be reused should be carefully and thoroughly cleaned in the appropriate method. Remove the splash shield next to the left front tire. Check the following and replace any faulty parts. If low voltage is still found after a two 2 hour charge, replace the battery according to the information in the warranty section of this bulletin. This process is accomplished by using containment envelopes as shown Type B.

Next

MAZDA MX

mazda mx 6 mazda 626 service repair workshop manual 1988 1989

Separate the fuel return pipe from the delivery pipe assembly. Connect a vacuum pump as shown in the illus­ tration. . Using this repair manual is an inexpensive way to keep you vehicle working properly. In Engine Compartment 1 Connect the black coupler to the solenoid valve which was installed in step 1.

Next

MAZDA MX6 626 PDF SERVICE REPAIR WORKSHOP MANUAL 1988

mazda mx 6 mazda 626 service repair workshop manual 1988 1989

This temporarily reduces line pressure and engages the lock-up clutch. Disconnect the coupler from the No. Tightening torque: 8—12 N-m 80—120 cm-kg, 69—104 in-lb 4. Position the camshaft caps according to the cap number and mark. Apply a continuous bead of silicon sealant to the oil pan along the inside of the bolt holes, and over­ lap the ends. Timing Belt Tensioner and Idler Pulley Check the timing belt tensioner and idler pulley for smooth rotation and abnormal noise.

Next

MAZDA MX

mazda mx 6 mazda 626 service repair workshop manual 1988 1989

If vehicle is a 1987 model, check the electrical system harness as follows: A. Note Make the system inspection first. Many people are afraid to touch their cars because it seems difficult. Tighten the camshaft pulley lock bolt. Tightening torque: 19—25 Nm 1.

Next

Mazda 626 Automotive Repair Manuals

mazda mx 6 mazda 626 service repair workshop manual 1988 1989

This is only the case if you do not have the resources and tools available when the time comes! Install the clutch release cylinder. Measure each piston ring end gap with a feeler gauge. Visually check the shutter valves for damage. If requested to return the failed fuel pump to Mazda, attach a copy of the check sheet and repair order. Caution Do not aliow any sealant to get into the oil hole.

Next

1988

mazda mx 6 mazda 626 service repair workshop manual 1988 1989

Start engine and confirm that the alternator warning light is not illuminated. Clean the rear quarter window glass and apply silicone between the glass and the garnish. Tightening torque: 8—12 Nm 80—120 cm-kg, 69—104 in-lb Oil Pan 1. Tightening torque: 19—25 Nm 1. Begin work only after first learning which parts and subassem­.

Next

Mazda 626 Automotive Repair Manuals

mazda mx 6 mazda 626 service repair workshop manual 1988 1989

Warm up the engine to normal operating temper­ ature and run it at idle. Failure to replace the timing belt may result in damage to the engine. No more messy manuals that you have to keep replacing or cant use any more due to wear and tear. Locate the hose at the inner panel corner as shown. Note The check connector is located at the rear of the left side wheel housing. If requested to return the failed air flow meter to Mazda, attach a copy of the check sheet and repair order.

Next

MAZDA MX

mazda mx 6 mazda 626 service repair workshop manual 1988 1989

Lots of people are terrified to touch their cars due to the fact that it appears tough. Apply silicon sealant to the shaded area shown in the figure. It also replaces the Midwest dealers formerly known as Mazda Great Lakes technical assistance phone number. In accordance with this design change, there is no interchangeability between new and old parts regarding the E. Required N Page 1 4 of 18. A table of contents at the beginning of each section placed. Although it is available on the market, reconditioned anti-freeze might contain silicon particles, which could abrade the water pump seal, or it might contain other chemicals, alcohol or methanol, that may erode metal parts.

Next