If you did not purchase the unit from Crutchfield, then you may want to contact the manufacturer, or try our online support center: I installed mine in a Honda Pilot. A major help was the Crutchfield technical hotline. Your bass tube should have come with a manual for hook up; if not, download it, as you will need it for installation. Sign up for an account now, or after you complete your purchase you'll get credit for the points either way. We thank you for your visit to our website. If you want to rattle windows or hear it from 100 feet away, it is not enough; but more than adequate if you want nice balance at moderate volumes. These efficiency differences result in the two woofers playing at different volume levels, making it difficult to adjust the system to the desired sonic quality.
. Two things I spent some time working on was finding a good rubber grommet in the firewall that was not being used for factory wiring. Improper power sources can reduce output and cause distortion. The Bass Tube enclosure's port and woofer are on the same plane and in close proximity for maximum corner-loading results. Now that the level is set, you may want to go back to the crossover control and adjust the crossover point by ear to meet the desired sonic quality of your system design. Be sure that the place you choose to flush mount the switch has enough clearance behind it before you start the installation of the switch.
If you install it in the cab of your car it will be way powerful. The corner of your car amplifies the concentrated bass output of the Bass Tube enclosure. I have spoken to tech suport at Bazooka Tube and even they haven't been able to help me. Start with the level control turned all the way to the right clockwise. If you do not have this style, you will need to hook up to a separate power lead from the fuse box or battery to power your sub.
Not looking to scare the neighbors, just wanted to balance my sound quality. Most of them contain a diagram to show you exactly where each port is located. It has plenty of power for the relatively small cab space, and it fills out the low end perfectly with windows down out on the highway during summer cruising. If the source unit has both front and rear speaker outputs, use only one set of speaker outputs for the high-level input of the Amplified Bazooka. Reverse polarity of one channel and check it again, the output should increase and the connections should be correct. Make sure you get the information you are looking for. Be sure to use a slave unit that is the same size as you amplified unit.
About Image description: Graphic has been published by author. This is the level control. The bass should be off or very low at this point. We thank you for your visit to our website. They can walk you through the different connections.
The factory wire harness in my vehicle which already had an amp from the factory has a separate hot lead from the fuse box along with the head unit lead for powering a separate amp so I did not need to hook up a separate wire for the sub. With the Jumper in the On Position, the Amplified Bazooka will turn on automatically when it senses any music. About the Author Alexis Lawrence is a freelance writer, filmmaker and photographer with extensive experience in digital video, book publishing and graphic design. Turn your points into Rewards Cards that you can use toward future purchases. You should have well enough length in wiring. Rehook your car battery once all connections are made and test your stereo.
Connect the Green wire from the 10-pin Molex plug of the Amplified Bazooka to the source units left + positive speaker output. Installing your own bass tube can be challenging, but if you are willing to invest some time in the project it can be done. The power wire carries substantial currents and could induce noise. The second thing was the routing of the wires from the dash to the rear of the car. This is the point in your system where you will get maximum volume with the least amount of distortion. An avid traveler, Lawrence has visited at least 10 cities on each inhabitable continent. Hitting a fuel line or electrical wire can do major damage.
If you have any problems with the registration process or your account login, please contact. This can be done easily with a pair of needle nose pliers. Also, as far as running the wire, take your time and be patient. I have an old Bazooka tube that I can't figure out the wiring. There are various main reasons why you are researching for information about bazooka tube wiring schematics, and surely, you are researching for new concepts for your purposes. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features.
If you are getting no sound from your Bazooka bass tube, you likely attached a wire to a negative battery terminal. Good bass is all about moving air, and a cylindrical tube translates the motion of its woofer into maximum air pressure so you hear and feel more bass. Well use it for much better future articles. Notice that one end of the mounting plate is angled and the other is not. Do not forget to share and love our reference to help further develop our website. With the head unit at this point, turn the level gain control up slowly until the bass volume blends well with the existing high frequency speakers. Hello Scott, If your amp draw from the head unit and sub at rated max output do not exceed the rated amp on the fuse, you will be ok doing this.
Connect the bass tube to your car stereo's power source. If you did not purchase the unit from Crutchfield, then you may want to contact the manufacturer, or try our online support center: If you purchased the product from Crutchfield, feel free to contact our Tech Support team. I read all the reviews, positive and negative, I asked questions while chatting with an online specialist, I compared the products side by side and narrowed down all my answers to my specific needs. The fuse is designed to prevent fire or damage to your car, should the battery wire short to ground. If you correctly attached all wires to the positive terminals in your stereo power source, you should hear the added bass. If anything is difficult, it would be routing the wires to keep them hidden. By buying this product you'll earn up to 150 Rewards points.